|
|
|
|
||||
|
Here's my contribution to the forum. I feel that this can be accomplished by anyone with the right tools, time, & patience.
A couple things first, I don't have any torque specs so if someone feels this is important & can supply them, I'll edit this. I didn't use any thread locker as none of the bolts seems to have it but given the vibrations, it might not be a bad idea. Tools needed: -Ramps or jackstands -Jack -Rachet & 5/8", 3/4", & 15mm sockets & 18mm deep socket -3 or 4" & 12" driver extensions -18mm wrench or adj. wrench -A breaker bar could also be helpful but I managed without. -Adj. bar clamp (see front trans). Time: Allow yourself 4hrs to play it safe. Install should be 2-3hrs depending upon issues encountered. Step 1) Use ramps or jack-up car & use jack stands then use a padded jack to support the trans close to rear trans mount. Step 2) Rear trans. Single bolt is 18mm & needs 3 or 4" extension & triple bolts are 15mm. I removed the single bolt then the triple. Contrary to appearance, you can remove the mount w/o removing the bracket it connects to mounted on the trans. Install in reverse process & leave triple bolts a little lose.  Step 3) Front trans. Again, use jack to support trans close to front trans mount. All bolts 18mm but top bolt requires wrech due to airbox clearance issue (airbox at top of image) & bottom 2 can use socket or wench. Remove bolts in any order but might be a good idea to loosen all a bit before removing any. When installing new mount, insert top-most bolt into mount before applying as clearing airbox is difficult. I threaded this bolt 1st, then the lower-front, then the bushing bolt. This was the hardest mount as it's difficult to get everything to line up, even with repositioning the jack. I ended up having to use an adjustable bar clamp to pull the engine/trans to the passenger side to get the bushing bolt in & again to be able to thread it. After you have the new mount on, go back & tighten the triple bolts on the rear trans mount.   Step 4) Front engine. Support engine with jack. Triple bolts on engine portion are 5/8". Frame-side bolts are 18mm (needs deep socket with extension & unless you're a brute, a breaker bar would be handy). Bushing bolt on solid mount is 3/4". Remove triple bolts on engine portion. Remove frame-side bolts. Notice sponginess of stock mount. Reverse for installing solid mount.  It can also be handy to have a Collie assistant to keep you company.   COMMENTS: I know there's already a very good review by thewastedyears but another can't hurt. First off, SOLID MOUNTS ARE NOT FOR EVERYONE!!! If your IRL is a daily driver, they might not be for you. If you're concerned about comfort, they're definatly not for you. They cause severe, very loud vibrations, especially at start-up, in lower gears, accelleration (seeing a trend?). I haven't tested with the A/C on but Wasted says that causes more vibes. The center gauge pod seems to vibrate the most & you can almost forget about using your rearview mirror. I haven't had a disc skip yet. Now, I'm not one to go around doing burnouts so I can't comment too much on that but I notice a lot more tire spinning just from driving around. I don't think there's any wheel hop, though, but I also have the traction bars so I doubt I could induce any. I did notice that when I opened it up to get on the freeway, I managed a 3rd gear scratch!  At some point, I might try swapping the stock front engine mount back in to see if that reduces the vibes w/o affect the benefit of the solid mounts too much. B.Woody, I don't know if softer bushings would work better. I think the greater problem with the stock mounts is the range of travel allowed as opposed to their softness. I had the GoofyGuy torque brace on prior but it honestly didn't help too much & when I was doing this install, I noticed one of the mounting brackets for it was bent (& I don't drive my car that hard). Thanks to B.Woody for the product & for the basic install info. |
|
|||
|
||||
|
my_bd
on
09-18-2006, 04:41 PM
|
|
I found that removing and installing the rear tranny mount is much easier, faster, less fiddly if you also remove the 3 bolts that hold the rear tranny bracket to the transaxle. it makes it easier to maneuver the old mount out and the new one into place, and then to realign everything.
The bracket has a wire/connector attached which you don't need to disconnect as long as you keep the bracket up in that general area, no need to take it right out. I torque all bolts to factory specs rear transaxle mount thru-bolt (single bolt) 66 ft/lb rear transaxle mount to subframe (3 bolts) 44 ft/lb rear transaxle mount bracket to transaxle (3 bolts) 41 ft/lb front transaxle mount thru-bolt 41 ft/lb front transaxle mount to transaxle (2 bolts) 41 ft/lb Engine mount to mid-rail (2 nuts) 74 ft/lb Engine mount to intermediate bracket (3 bolts) 37 ft/lb BWoody engine mount through bolt ??? ft/lb reference http://manual.lsjowners.com/trans/mu3fast.htm http://manual.lsjowners.com/engine/fasten_4.htm |
|
|
Hyperion
on
09-18-2006, 07:20 PM
|
|
|
Quote:
 "Scary" I think is the best description. Def not something I'm used to. I keep expecting to throw a code, go into limp mode, or for something to break. I just installed them yesterday so I don't have a lot of miles on 'em. There's no doubt that they put more power to the ground, though. |
|
|
|
|
wasntme
on
09-19-2006, 07:00 AM
|
|
welcome to my world solid mounts are definitly not for everyone, the power transfer is greatly improved as you should have already noticed, as far as the vibrations it will take some getting used to but give it about 2-3 weeks and you'll forget about them trust me. I have our mounts in my srt4 as well mine vibrates more than the RL its like second nature now i think i'd have to relearn how to shift with the stockers if i placed them back in and relaunch at the track but that will never happen i like the power transfer too much....hehe
|
|
|
|
sheek360
on
09-19-2006, 07:05 AM
|
|
|
Quote:
|
|
|
|
 |
Similar Tutorials
|
||||
| Tutorial | Tutorial Starter | Forum | Replies | Last Post |
| OE solid filled motor mounts | sscavy | Buy/Sell Parts | 13 | 09-25-2007 04:42 PM |
| Torque Forward's Solid Mounts | rlinbatonrouge | Product Reviews | 3 | 03-05-2006 11:42 AM |
| OE Solid filled motor mounts | sscavy | Performance Modifications | 16 | 10-30-2005 04:40 PM |
| Currently Active Users Viewing This Tutorial: 1 (0 members and 1 guests) | |
| Tutorial Tools | |
| Display Modes | |
|
|
Linear Mode
