Saturn ION RedLine Forums banner

Latest activity

  • Eagle_f90 replied to the thread Oil consumption.
    You should see my car. Not a spec of rust on it and even has the factory antirust protetion on it. Your compression numbers look good...
  • Chris Morin replied to the thread Oil consumption.
    When I pulled the car in yesterday morning, adding oil was the last thing I did after pulling the air filter spark plugs, doing the...
  • Blk06CompIRL replied to the thread Oil consumption.
    Random other thought. After our engines run they do need a long time , sometimes up to 30 min, for all the oil to run back down. Have...
  • goaliemo replied to the thread Rear brake pad headache.
    You can buy a similar kit from hobo freight for I think it's $40 now. They've gotten high with the prices as everyone else.
  • Aapoo replied to the thread Rear brake pad headache.
    Yessir I did do that. And the tool from O'REILLY'S helped tremendously. Like from hours on the right side, to minutes on the left. Thank...
  • Chris Morin replied to the thread Oil consumption.
    Coolant is clean.
  • Eagle_f90 replied to the thread Oil consumption.
    How does your coolant look? Poasibly leaking into there?
  • goaliemo replied to the thread Rear brake pad headache.
    Hit it with some pb blaster or equivalent. It may of seized up
  • Aapoo replied to the thread Rear brake pad headache.
    Thank you gents. This is all previously unknown information. I did manhandle the left rear and now the wheel seems locked up. The...
  • Chris Morin replied to the thread Oil consumption.
    I put the car up on the lift this morning and looked underneath. Everything is dry as a bone. The only thing I see under there is some...
  • cavingman replied to the thread Is this a problem.
    you should be fine, you might be able to wrap it with something like rubber hose if boost leaks though. I have a brand new unused stock...
  • goaliemo replied to the thread Rear brake pad headache.
    You can also rent the kit to do em at O'Reilly's. I did that the first time before I bought one of the all in one deals
  • Blk06CompIRL replied to the thread Clutch Job.
    I had good luck with lifting the front of the car up and vacuum pump on master cylinder for 1hr, release to vacuum from the pump and...
  • Chris Morin replied to the thread Oil consumption.
    I will definitely pull the air filter and check that too. Thanks.
  • Blk06CompIRL replied to the thread Rear brake pad headache.
    Make sure parking brake is released as well if for some reason you applied it and man handled the caliper off. (I've seen it done...
  • Eagle_f90 replied to the thread Baro sensor part #.
    Dont know if you have ordered this yet or not but wanted to throw it out there that i am parting out an 06 redline due to rust and i...
  • Blk06CompIRL replied to the thread Oil consumption.
    Check your air filter for oil staining indicating excessive oil going through the pcv system, and most likely caused by excessive blow...
  • Chris Morin replied to the thread Oil consumption.
    I'm going to throw it up on the lift tomorrow and take a peek around. I'll pull the plugs and see how things look as well. I just...
  • goaliemo replied to the thread Oil consumption.
    Most things are acceptable with GM I've noticed my few months working there. How do the plugs look? It's just odd that if it's not...
  • Besign BK01 Bluetooth 4.1 Car Kit... https://www.amazon.com/dp/B01MSUWCZ0?ref=ppx_pop_mob_ap_share Run power to the power plug in the...
  • I've noticed over the last couple oil changes on my '07 Ion SC 2.0 that my oil level is getting low after only a couple thousand miles...
  • goaliemo replied to the thread Rear brake pad headache.
    You trying to push? Or did you get the tool to spin it?
  • Having a heck of a time getting the piston to go in far enough to get the pads over the rotor. Any advice would be splendid.
  • goaliemo replied to the thread Baro sensor part #.
    Hopefully that does it. Seems like that's the only thing left if you have digitals going to it
  • Dappersworth replied to the thread Baro sensor part #.
    Thank you so much! Hopefully I can get this baro code to go away now. Edit: it seems i misspelt the part number, it's 19418810 not...
Top